Publish Time: 2019-07-23 Origin: Site
Have you ever purchased and used an oxygen compressor? In fact, even if it is simple, using an oxygen compressor is not an easy task. However, the maintenance of the oxygen compressor is equally important.
Main:
How to use an oxygen compressor?
Oxygen compressor routine maintenance and precautions
In conclusion
How to use an oxygen compressor?
Using an oxygen compressor is not as complicated as you might think, it's actually very simple. After the compressor is installed, it can be put into normal operation after normal test. If you want to adjust a parameter, please follow the steps below:
The machine usually has 2 pressure switches. Finding the one you need to adjust not only needs to know how to use the oxygen compressor, but also the maintenance of the oxygen compressor, because it is related to normal use. Control principle: Loading pressure (starting pressure) + differential pressure = stop pressure.
l When adjusting, take the pressure gauge as the standard and loosen the tightening nut;
l Reduce the loading pressure: rotate the pressure adjusting screw clockwise (pointer up, pressure decrease) for half a week, observe whether the loading pressure meets the requirements (because the pressure difference is not adjusted, the stopping pressure will change accordingly), if not, adjust it appropriately.
l Increase the pressure difference: rotate the differential pressure adjustment screw counterclockwise (the pointer moves down, the pressure difference increases) for half a week, and observe whether the pressure difference is the stop pressure or not, if no adjustment is made.
l After each pressure value is reset, lock the nut and correct the parameters once. Increase the loading pressure or reduce the pressure difference and reverse the adjustment as described above. The inlet pressure switch adjustment method is basically the same, but the wiring method is different, the stop pressure at this time = starting pressure - differential pressure. It is strictly forbidden to operate the machine above the rated exhaust pressure.
Each stage of the compressor is equipped with a temperature controller, which is installed on the control cabinet panel and is set at the factory.
Set it, if you need to reset, please refer to the manual of the intelligent temperature controller.
The thermal relay acts as a motor overload protection. Occasionally, the motor will stop rotating. If the set value is determined to be malfunctioning, it should be properly adjusted by professional electric work, and the running current should be measured. When the compressor is working normally, there is less work to be maintained, but it must be handled by a special person. It should be patrolled twice per shift to observe whether the compressor has abnormal heat, abnormal vibration, abnormal sound, etc. If it is necessary, stop it immediately. After confirming the troubleshooting, you can continue to run. At the end of each shift, the power should be turned off and the intake valve closed. In order to ensure long-term reliable operation of the machine, it must be checked regularly.
1.When the compressor is running, it must carefully carry out necessary inspections and inspections, monitor the operating conditions of the compressor, closely monitor the suction, exhaust pressure and temperature, exhaust volume, cooling water temperature and other control indicators, pay attention to abnormal noise, and Record every once in a while.
2. During the operation, the process gas is strictly prevented from being crushed into the low-pressure cylinder and other gas pipelines by the high-pressure cylinder to prevent oil, water and liquid.
3. It is forbidden to operate the compressor under over-temperature, over-pressure and over-speed. If there is any abnormality, you should carefully remove the fault and report it in time.
4. Gas leakage When the vehicle is in emergency stop, the power should be cut off in the substation.
5. When repairing the equipment, carefully check the maintenance license and the relevant safety inspection regulations to ensure the safety of the inspection.
6. When using an oxygen compressor, do not use oily sand to wipe the equipment, pipes, valves and accessories. Do not be contaminated by oil. Degreasing treatment should be carried out after inspection, and flammable gas leakage monitoring equipment should also be provided.
7. Check the machine room and arbitrarily stack flammable materials.
You don't have to worry about the quality of the compressor, because our oxygen compressors, nitrogen compressors, CO2 compressors, etc. have passed the EU CE certification and are recognized for the safety of the compressor. If you still don't know how to use it, you can consult us. But be sure to pay attention to maintenance work.